Drilling mud gas separator for solids control

Drilling mud gas separator for solids control

Mud Gas Separator is commonly called a gas-buster or poor boy degasser. It captures and separates large volume of free gas within the drilling fluid. If there is a “KICK” situation, this vessel separates the mud and the gas by allowing it to flow over baffle plates.

The gas then is forced to flow through a line and vent it to a flare. A “KICK” situation happens when the annular hydrostatic pressure in a drilling well temporarily (and usually relatively suddenly) falls below that of the formation, or pore, pressure in a permeable section downhole, and before control of the situation is lost.

It is always safe to design the mud/gas separator that will handle the maximum possible gas flow that can occur.

DSCI0562_副本

FLQ series Mud gas separator

FLQ series Mud gas separator (Poor Boy Degasser) is professional equipment to treat the gas invade mud. When the drilling mud result gas invades, the proportion of its weight and viscosity has a greater deviation not to meet the requirements of drilling. The serious situation is that would cause Chung well, and even blowout accident occurred, if not to treat it timely.

FLQ series Mud gas Separator combined with the Electric Ignition Device can be used to ensure the drilling process smooth. It is devided into the normal pressure Mud gas separator and pressure auto-control Mud gas separator, according to the pressure. Mud gas Separator is your best choice to prevent drilling mud invasion.

FLQ Series Mud gas separator Technical Parameters

Model

FLQ800

FLQ1000

FLQ1200

Vessel diameter

 Ø800mm

 Ø1000mm

 Ø1200mm

Treating capacity

 240m3/h

 300m3/h

 380m3/h

Feed inlet

 5″

 5″

 5″

Fluid discharge

 8″

 10″

 10″

Vent line

 8″

 8″

 8″

Weight

 1650kg

 2000kg

 2000kg

Dimension

 1900×1900×5700mm

 2000×2000×5860mm

 2200×2200×6634mm

Remark

  1. Vent line length depends on user’s demand
  2. Customizable vessel diameter, mud seal/leg

 QQ截图20131129100842_副本

Mud gas separator for drilling fluids control

Mud gas separators in other countries also called Poor boy degasser, Liquid-gas separators, Mud/Gas Separators, etc. OGEM Solids Control designs and manufactures FLQ Mud gas Separators. Mud gas Separators is an extremely reliable, vital piece of safety equipment for today’s drilling operations.

It is ideal for use where drilling is likely to encounter large volumes of gas, sour gas or when an operator is drilling with an under balanced mud column. This Mud gas Separators is primarily used to separate and safely vent large pockets of free gas, which may include toxic gases such as hydrogen sulfide, etc. from the drilling fluids processing system.
Buy Solids control Mud gas separator for solids control system, drilling fluids, well drilling solids control Mud gas separator from China manufacturer-OGEM solids control.

 

Introduction of Drilling mud – Poor boy degasser

OGEM Solidscontrol manufacture mud gas separator in oilfield drilling mud cireculation system .

Mud gas separator is also called Poor boy degasser,Gas-Liquid separator. It captures and separate large volume of free gas within the drilling fluid. If there is a “KICK” situation , this vessel separates the mud and the gas by allowing it to flow over baffle plates.

The gas then is forced to flow through a line and vent it to a flare. A “KICK” situation happens when the annular hydrostatic pressure in a drilling well temporarily (and usually relatively suddenly) becomes less than the formation, or pore, pressure in a permeable section downhole, and before control of the situation is lost. It is always safe to design the mud/gas separator that will handle the maximum possible gas flow that can occur.

QQ截图20131129100842_副本

FLQ series mud gas separator From OGEM Solids Control

FLQ series Mud gas separator is professional equipment to treat the gas invade mud. When the drilling mud result gas invade, the proportion of its weight and viscosity have a greater deviation not to meet the requirements of drilling. The serious situation is that would cause Chung well, and even blowout accident occurred, if not to treat it timely.

FLQ series mud gas Separator combined with the Electric Ignition Device can be used to ensure the drilling process smooth. It is devided into the normal pressure mud gas separator and pressure auto-control gas-liquid separator, according to the pressure.Mud Gas  Separator is your best choice to prevent drilling fluids invasion.

Principle of Operation

The principle behind the mud gas separator is relatively simple. The mud and gas mixture is fed at the inlet allowing it to impinge on a series of baffles designed to separate gas and mud. The free gas then is moved into the flare line to reduce the threat of toxic and hazardous gases and the mud then discharges to the shale shaker and to the tank.

Gas-liquid separators in other countries also called Poor boy,Liquid-gas separators,Mud/Gas Separators, etc.OGEM Equipment designs and manufactures FLQ Gas-Liquid Separators.

QQ截图20131129101427_副本

Gas-Liquid Separators is an extremely reliable, vital piece of safety equipment for today’s drilling operations. It is ideal for use where drilling is likely to encounter large volumes of gas, sour gas or when an operator is drilling with an underbalanced mud column.

This Gas-Liquid Separators is primarily used to sep – arate and safely vent large pockets of free gas, that may include toxic gases such as hydrogen sulfide, etc. from the drilling fluids processing system.

Buy Solids control Gas-liquid separator for solids control system,drilling fluids,well drilling solids control Gas liquid separator from China , please contact OGEM Solidsontrol.

 

Oil/gas drilling rig poor boy degasser

Oil/gas drilling rig poor boy degasser

Poor boy degasser is an efficient item to get rid of large quantities of toxic gas among drilling fluid. This blog will introduce more info on poor boy degasser about the basic structure, the simple principle and how to design a poor boy degasser.

200971014021439_副本

Poor boy degasser structure

We all know, poor boy degasser is also called mud gas separator or gas buster. One glossary ever described it as a simple separator vessel used to remove free or entrained gas from fluids circulated in the wellbore, such as mud used during drilling operations. The gas buster typically comprises a vessel containing a series of baffles with a liquid exit on the bottom and a gas-vent line at the top of the vessel.

Above is a simple description on poor boy degasser. The oil and gas drilling rig poor boy degasser completely includes base support, main vessel, fluid inlet, baffles, drain valve, vent line, discharge output, pressure gauge, relief valve, and lay down legs.

If requested by clients, the vent line should be supplied together with degasser. Usually, there will be 30m or 50m for option.

200993162234284_副本

Oil rig poor boy degasser principle

Oil rig poor boy degasser basic working principle is the drilling fluid flow into feed inlet. After going through baffles the air bubble will break down and flow up. The drilling mud will flow down till the discharge output. It is different with vacuum degasser

We know, on poor boy degasser, there is necessary mud seal/mud leg.  U tube on discharge output will result the mud seal. Its function and effect is to prevent discharged gas flow together with drilling fluid after degassing.

Usually, for oil and gas drilling rig, after the poor boy degasser the drilling fluid will flow to shale shaker for subsequent solids control process.

Above is the simple principle of poor boy degasser working. Following will be the design on poor boy degasser.

QQ截图20131129100842_副本

How to design poor boy degasser

Former content introduced basic principle and structure. So now the design is more simple and clearer.

First of all, the poor boy degasser is almost designed as vertical type. It is closed bottom vessel type. Poor boy degasser for oil and gas drilling rig includes 600mm, 800mm, 1000mm, and 1200mm diameter.  The feed inlet usually is 5″, output discharge is 10″ or 8″, while the vent line will be 8″ diameter. But customizable dimension is available upon users’ demand.

The poor boy degasser feed inlet connected with choke manifold. The output line will be connected with shale shaker inlet line or flow divider. Vent line is connected to flare line.

 Regarding to the liquid leg, we usually design it as 12 ft line. As we said before, the mud seal will prevent drilling mud with remain toxic. Sufficient mud seal will lead good performance. Furthermore, there will be 4-5 baffles mounted on vessel wall.

Finally, is to design the support base. It can be fixed type or elevating/folding type. More and more clients prefer the folding base poor boy degasser for its flexibility and convenience at oil drilling job site.

QQ截图20131129101427_副本

Please find sketch for reference. General information is as above content. Detail and certain design will be provided according to actual working condition. If you need poor boy degasser, please contact OGEM Equipment. We have poor boy degasser for sale now.

 

Poor Boy Degasser/Mud Gas Separator Supplier from China

What is the Mud Gas Separator?

Mud Gas Separator(Poor Boy Degasser) is a specific degassing equipment of drilling fluid with gas, it is mainly used to remove big bubbles in diameter more than φ3mm in gas drilling fluid.

If the big bubbles’s diameter is greater than φ3~φ25mm, which will make the drilling fluid’s gravity and viscosity ratios deviated greatly, the mud will not meet the demand of drilling, even further more, a worse situation of gas in drilling fluid will cause well kick or blowout.

Gas invaded drilling fluid enters the separator from the liquid inlet tangential. Along the wall fell in a specially designed a series of inside baffle, collision, increase the exposure surface area, flows down words, cause turbulent flow, separate the drilling fluid. Free gas was discharged through the separator top of the gas exhaust pipe, (pipe length shall not be less than 50 meters) and led to the safe area using Flare Ignition Device can ignite gas. The degassing of drilling fluid was sent into shale shaker inlet or shale shaker distributer.

AJGS Mud gas separator

OGEM Solids Control Equipment Poor Boy Degasser

OGEM FLQ Series poor boy degasser(mud gas separator)is the primary equipment to remove invaded gas.This euquipment has the advantages of simplified design,hign efficient,conveient to install and operate.It is important safety device to prevent blowout in oilfiled.

Benefits:

1.Certificate of international contiater pressure requirement;

2.Big volume can remove posion gas efficiently;

3.Easy to install,free lifting adjustment;

4.Improve the effectiveness and raliabilty of the optimization process.

OGEM Solids Control Equipment is professional manufacturer on hiqh quality degassers including mud gas separator and gas buster.

The quality and standard is according to ISO9001-2000. Find more oil and gas mud equipments at OGEM .More need can cantact us.

 

 

 

New type Poor boy degasser from China

Brief introduction of poor boy degasser

We OGEM manufacture mud gas separator in oilfield drilling mud cireculation system .

200993162234284_??
Mud gas separator is also called Poor boy degasser, Gas-Liquid separator. It captures and separate large volume of free gas within the drilling fluid. If there is a “KICK” situation , this vessel separates the mud and the gas by allowing it to flow over baffle plates.

The gas then is forced to flow through a line and vent it to a flare. A “KICK” situation happens when the annular hydrostatic pressure in a drilling well temporarily (and usually relatively suddenly) becomes less than the formation, or pore, pressure in a permeable section downhole, and before control of the situation is lost.

It is always safe to design the mud/gas separator that will handle the maximum possible gas flow that can occur.

200971014021439_??

FLQ?series mud gas separator From OGEM Solids Control

FLQ series Mud gas separator is professional equipment to treat the gas invade mud. When the drilling mud result gas invade, the proportion of its weight and viscosity have a greater deviation not to meet the requirements of drilling.

The serious situation is that would cause Chung well, and even blowout accident occurred, if not to treat it timely.?FLQ series mud gas Separator combined with the Electric Ignition Device can be used to ensure the drilling process smooth.

It is devided into the normal pressure mud gas separator and pressure auto-control gas-liquid separator, according to the pressure.Mud Gas ?Separator is your best choice to prevent drilling fluids invasion.

Principle of Operation

The principle behind the mud gas separator is relatively simple. The mud and gas mixture is fed at the inlet allowing it to impinge on a series of baffles designed to separate gas and mud.

The free gas then is moved into the flare line to reduce the threat of toxic and hazardous gases and the mud then discharges to the shale shaker and to the tank.

Gas-liquid separators in other countries also called Poor boy,Liquid-gas separators,Mud/Gas Separators, etc.OGEM Equipment designs and manufactures FLQ Gas-Liquid Separators.

Gas-Liquid Separators is an extremely reliable, vital piece of safety equipment for today?s drilling operations. It is ideal for use where drilling is likely to encounter large volumes of gas, sour gas or when an operator is drilling with an underbalanced mud column.

This Gas-Liquid Separators is primarily used to sep – arate and safely vent large pockets of free gas, that may include toxic gases such as hydrogen sulfide, etc. from the drilling fluids processing system.

Buy Solids control Gas-liquid separator for solids control system,drilling fluids,well drilling solids control Gas liquid separator from China , please contact OGEM.

 

Poor boy degasser/ Mud gas separator in Solids control

Introduction of mud gas separator

Mud Gas Separator is commonly called a gas-buster or poor boy degasser. It captures and separates large volume of free gas within the drilling fluid. If there is a “KICK” situation, this vessel separates the mud and the gas by allowing it to flow over baffle plates.

The gas then is forced to flow through a line and vent it to a flare. A “KICK” situation happens when the annular hydrostatic pressure in a drilling well temporarily (and usually relatively suddenly) falls below that of the formation, or pore, pressure in a permeable section down hole and before control of the situation is lost. It is always safe to design the mud/gas separator that will handle the maximum possible gas flow that can occur.

1

The principle of mud/gas separation for different types of vessels is same. The types of closed bottom type, open bottom type and float type. According to pedestal or base type there are fixed type and elevating type. Poor boy degasser in China is usually named according to vessel diameter. So the type also incurs FLQ800 or ZYQ 800, FLQ1000, FLQ1200 and FLQ1400. Usually, the degasser?s type or configuration is customizable.

Principle of operation

The principle behind the mud gas separator is relatively simple. On the figure, the mud and gas mixture is fed at the inlet allowing it to impinge on a series of baffles designed to separate gas and mud. The free gas then is moved into the flare line to reduce the threat of toxic and hazardous gases and the mud then discharges to the shale shaker and to the tank.

 

Mud gas separator for drilling fluids solids control

Mud gas separators also called Poor boy degasser, Liquid-gas separators, Mud/Gas Separators, etc in other countries. OGEM Solids Control?designs and manufactures FLQ Mud gas Separators. Mud gas Separator is an extremely reliable, vital piece of safety equipment for today?s drilling operations. It is ideal for use where drilling is likely to encounter large volumes of gas, sour gas or when an operator is drilling with an under balanced mud column. This Mud gas Separators is primarily used to separate and safely vent large pockets of free gas, which may include toxic gases such as hydrogen sulfide, etc. from the drilling fluids processing system.

4

FLQ series Mud gas separator

  • FLQ series Mud gas separator (Poor Boy Degasser) is a professional equipment to treat the gas invading mud. When the drilling mud result gas invades, the proportion of its weight and viscosity has a greater deviation not to meet the requirements of drilling.

 

  • The serious situation is that would cause Chung well, and even blowout accident occurred, if not to treat it timely FLQ series Mud gas Separator combined with the Electric Ignition Device can be used to ensure the drilling process smooth.

 

  • It is divided into the normal pressure Mud gas separator and pressure auto-control Mud gas separator, according to the pressure.

?200971014021439_??

Mud gas Separator is your best choice to prevent drilling mud invasion. When you need, you can contact us freely, the best price and quality will be served.

HDD Mud recycling system for sale

What’s HDD?

HDD is the horizontal directional drilling. It is one kind of no dig or trenchless drilling. What is HDD mud recycling system? Many new players in drilling industry or in HDD industry don’t understand about Mud recycling system. Let?s find interesting info as below:

HDD MUD RECYCLING SYSTEM GENERAL INFORMATION

]6DQ[1N{QEYE]BQA3WVWEDH

  • Horizontal directional drilling?is different with oil and gas drilling, water well drilling, etc. vertical drillings. So the mud process or solids control will be different also. The HDD mud process is called recycling since its point and issue is to recycle the drilling mud.

 

  • After processed by mud equipments, some of drilling mud will be used again and some of waste subject will be treated accordingly or delivered to certain place for other application.

 

  • To design HDD mud recycling system we usually consider the drilling rig size and name the mud system combine rig counter-expanding force, or based on mud pump flow rate.

 

100t Rig?Mud Recycling system for sale

 

1. At OGEM we have one 100T HDD mud recycling system for sale. The whole treating capacity is 200GPM. The main configuration is shale shaker, one mud tank, one set desilter, one slurry pump to feed shale shaker, one centrifugal feeding pump to feed desilter.

2. Furthermore, we configured mud mixing pump mounted on mud tank. The mixing hopper pump is combined with small Ventura?hopper and one 11KW centrifugal pump. The cost is about USD40000 for complete mud recycling system based on FOB Xingang, China.

3. We ever designed one 200GPM system for a client match their DRILLTOOLS rig. They are satisfied with our mud system. We know there will be many potential users on such mini mud recycling unit. Then we have finished it long time.

4. If you are interested please contact us for the latest price. Or you have any further questions just contact us freely.

Another HDD fluids system

Other HDD MUD SYSTEM FOR SALE AT OGEM

 

We OGEM is a professional manufacturer on solids control, including in petroleum industry oil and gas drilling, HDD mud process, mining or exploration slurry separation, waste management, etc.

OGEM can provide mud recycling system for following HDD rig. Including 45~60T rig, 100T rig, 200T HDD rig, 300T rig, and 450T rig. We can match our mud system for Varmeer rig, DRILLTOOL rig, and etc. many brands HDD rig.?As we said just now the “T” means the extension force.

The treating capacity can be from 200GPM~500GPM. These are common configurations used in HDD industry mud process. For each system the main difference is the treating capacity. General design and configuration is similar.

DSC03476

who makes?HDD mud system?

As we know, there is Mud puppy, Kemtron, DFE, OGEM, FSI, etc. ?They are experienced manufacturer and almost are world famous brand.

What do you need? What detail do you request? Please feel free to contact us.

Mud/gas separator & FLQ Poor boy degasser from China

Definition?

Mud/gas separator also called poor boy degasser and gas buster. It is special device to separate gas during oil & gas drilling. Following is the advantages of FLQ Series poor boy degasser:

200971014021439_??

THE description

  • FLQ Poor boy degasser is designed by OGEM Equipment. The main construction and principle is same as other types mud/gas separator. While our main models including following specifications. We can also find more information via degasser pictures.

 

  • Poor boy degasser with 5? feed inlet, 8″ and 10″ mud discharge, while 8″ vent line/gas discharge, while degasser vessel generally including 24″, 32″, 40″, 48″ dia. The degasser vessels thickness can be 8mm, 10mm, 12mm, 14mm according to users’ demand and actual poor boy model.

 

  • The vessel can be made of common carbon steel Q235, or?Q345/16MnR. If our degasser will be used under H2S gas condition, kindly suggest that adopt common carbon steel Q235.

 

  • Another issue is the degasser mud seal/leg. We ever talked this many times. The mud seal is one U tube on mud discharge line. Its height can be customized as per customer?s requirements or according to degasser?s other configuration.

Parameters as follow:

Model

FLQ800

FLQ1000

FLQ1200

Vessel diameter

?800mm

?1000mm

?1200mm

Treating capacity

240m3/h

300m3/h

380m3/h

Feed inlet

5?

5?

5?

Fluid discharge

8?

10?

10?

Vent line

8?

8?

8?

Weight

1650kg

2000kg

2000kg

Dimension

1900*1900*5700mm

2000*2000*5860mm

2200*2200*6634mm

Remark

  1. ?Vent line length depends on user?s demand??????? 2.Customerizable vessel diameter , mud seal/leg

200993162234284_??

THE ADVANTAGES????

OGEM Equipments are professional producers on oil drilling fluid equipments. Our poor boy degassers are high efficiency, with high process capacity. They are still used in drilling in various conditions.

They can removal of dangerous H2, and other toxic gas, free gas, promotes safe rig environment. The specifications and configurations are customizable for different well drilling programs.

When you have interest, you can contact us freely. The best quality and price will give you good impression. Hope cooperation!

Mud gas separator in mud treating

Oil/gas drilling rig poor boy degasser

Poor boy degasser is an efficient item to get rid of large quantities of toxic gas among drilling fluid. This blog will introduce more info on poor boy degasser about the basic structure, the simple principle and how to design a poor boy degasser.

200971014021439_??

Poor boy degasser structure

  • We all know, poor boy degasser is also called mud gas separator or gas buster. One glossary ever described it as a simple separator vessel used to remove free or entrained gas from fluids circulated in the wellbore, such as mud used during drilling operations. The gas buster typically comprises a vessel containing a series of baffles with a liquid exit on the bottom and a gas-vent line at the top of the vessel.

 

  • Above is a simple description on poor boy degasser. The oil and gas drilling rig poor boy degasser completely includes base support, main vessel, fluid inlet, baffles, drain valve, vent line, discharge output, pressure gauge, relief valve, and lay down legs.

If requested by clients, the vent line should be supplied together with degasser. Usually, there will be 30m or 50m for option.

Oil rig poor boy degasser principle

1. Oil rig poor boy degasser basic working principle is the drilling fluid flow into feed inlet. After going through baffles the air bubble will break down and flow up. The drilling mud will flow down till the discharge output. It is different with vacuum degasser.

2. We know, on poor boy degasser, there is necessary mud seal/mud leg. ?U tube on discharge output will result the mud seal. Its function and effect is to prevent discharged gas flow together with drilling fluid after degassing.

3. Usually, for oil and gas drilling rig, after the poor boy degasser the drilling fluid will flow to shale shaker for subsequent solids control process.

200993162234284_??

Above is the simple principle of poor boy degasser working. Following will be the design on poor boy degasser.

How to design poor boy degasser

Former content introduced basic principle and structure. So now the design is more simple and clearer.

First of all, the poor boy degasser is almost designed as vertical type. It is closed bottom vessel type. Poor boy degasser for oil and gas drilling rig includes 600mm, 800mm, 1000mm, and 1200mm diameter. ?The feed inlet usually is 5″, output discharge is 10″ or 8″, while the vent line will be 8″ diameter. But customizable dimension is available upon users’ demand.

The poor boy degasser feed inlet connected with choke manifold. The output line will be connected with shale shaker inlet line or flow divider. Vent line is connected to flare line.

Regarding to the liquid leg, we usually design it as 12 ft line. As we said before, the mud seal will prevent drilling mud with remain toxic. Sufficient mud seal will lead good performance.?Furthermore, there will be 4-5 baffles mounted on vessel wall.

Finally, is to design the support base. It can be fixed type or elevating/folding type. More and more clients prefer the folding base poor boy degasser for its flexibility and convenience at oil drilling job site.

If you need poor boy degasser, please contact OGEM Equipment. We have poor boy degasser for sale now.